Posted on

Ask a Question

Post a question/comment below and we’ll answer it as soon as we can.

Note – Before you ask the question, “Will my drill work?”, please review the drill minimum requirements and the specs of your particular drill.

167 Questions

  1. need to purchase 8in blades we have two companys that we order from they are out stock do not know when they be getting more

    1. Please contact AWC Distributing at 952/224-3649 during normal business hours or order direct from our website
      We do have them in stock.

  2. Can the k drill be used on a power auger head unit. I have the strike master Honda.

    1. Yes, the K-Drill can be used on a gas powerhead. I’m familiar with fitting them onto Strikemaster and Eskimo powerheads. As long as the output shaft is 7/8″ dia and rotates clockwise when viewed from the top, it will work. In some cases if the same bolt that was used to hold the steel auger onto the gas power head is not fitting through the hole of the K-Drill, it may be necessary to drill another hole through the collar of the K-Drill shaft and secure the K-Drill with a bolt and nut. This new hole is to be drilled at 90 degrees to the existing mounting hole.

  3. I received my new 6″ K Drill today and one of the flights is broken. How do I go about getting it replaced?

    1. IF it was broken in shipment from Thorne Bros., then it should be returned to them for replacement. If you don’t want to wait for the return and exchange, then get it sent in to us at the address below an we will repair.
      Send to
      AWC Distributing
      6667 West Old Shakopee Rd
      Suite 101
      Minneapolis, MN 55438
      Please include your name, address and phone number and the nature of the return and we’ll repair it and get it sent back to you.

  4. I just purchased a 8″ k drill. Is my Dewalt dcd990 up to the task?

    1. It would be a little light on power output. It has 650 UWO and the DCD991, that we recommend has 820 UWO. I’d sooner er to the more powerful side than have you disappointed with the drill and the auger because it just won’t carry the load for the long run.

  5. I just purchased an 8″ K Drill and looks like it will work great. My questions is regarding the size, 8″. The box read that it is an 8″ drill but seems a bit smaller than 8″. According to how I measured it is almost 7″. I have an 8″ gas auger and when I compare, the K Drill does seem smaller.

    Is that right? Or did I get the 6″ auger by mistake? Just want to be sure and wondering if I need to exchange.

    1. When measuring from outside blade tip to outside blade tip the 6″ K-Drill drills a full 6″ diameter hole. The 8″ K-Drill drills a 7.5″ diameter hole.

  6. Thinking about buying the 6in kit combo, wanted to know how many batteries either drill comes with in the combo pack.

    1. We offer the Milwaukee 2703-22 or the DeWalt DCD991P2 in our combo packs. Both the Milwaukee and Dewalt come with 2-5 amp/hr lithium ion batteries in the combo.

  7. Hello, I have a brushless non fuel m18 drill and do not want to spend 150 on this Auden for it not to work will my model work model: 2701-21p

    1. We put in drill requirements in our manual as well as on our website. Judging from looking up the model number of the Milwaukee drill, it falls short of the necessary drill requirements. We’re sorry, but we’d sooner lose the sale of a K-Drill than have a customer that’s disappointed in the performance of their drill and our auger.

  8. Side Stabilizer Handle disconnecting-breaking the casting on the Milwaukee while drilling (second time this has happened), often happening when nearing the end of the hole. Very hard on the wrist. What setting and # should I have it on (lowest = 1?) and drill mode right?

    1. The design of the side stabilizer arm mounting on the Milwaukee drill requires that it be kept very tight at all times. We’ve heard of persons actually adding an internal tooth lockwasher to this arm to help keep it tight during drilling. If you don’t like the idea of sending the drill back to Milwaukee for them to repair, the Clam Plate solves this issue because the ears are not used to hold it into position. The down side is adding an additional 5 lbs of material to the hole drilling experience.

  9. I have Milwaukee 2703-20 and K drill 8 in with drill set on 1 and drill mode. The unit is only 1 year old with less than 100 holes drilled. The drill is slipping and ratcheting to the point of not getting through 18 inches of ice.

    1. That is a drill issue and the drill will need to be returned to Milwaukee for repair. Contact or call 1-800-729-3878

  10. Can I attach my Kdrill auger to my Jiffy Legend power head and will it work ok?

    1. I’m afraid not. Jiffy’s turn counterclockwise and the K-drill turns clockwise.

  11. I have two sons 12 and 14 who are very responsible and love to ice fish. I want to purchase a k drill for them to use they fish tip ups and pan fish equally. Is the 6 inch easier to use ( less binding or grabbing at break through than the 8 inch) or is there no difference other than the amount of holes you can drill. I have a milwaukee fuel 2703 for them to use. Just looking for advice about which one they may experience the least amount of potential issues. Thanks

    1. I think the 6″ k-drill would be a better choice for them because they will not be patient enough to stay in one spot all day long and will want to drill more holes than we as parents. The 6″ will provide them with adequate hole size for the fishing experiences and will allow them approx. 15% more holes per battery charge. The amount of torque difference between the 6″ and 8″ is very small.

  12. Morning Tom, how did you get the bubble level to stay on your Fuel drill? Super glue cracked off and I don’t want to glob it up with silicone. K Drill is a great product!

    1. A single large drop of silicone should hold the bubble level in position on the end of the drill. The silicone also has some resilience to handle any vibration you may experience as well. It’s also possible to use hot-melt glue but you will need to be quick to get it correctly located before hardening.

  13. I have a Craftsman 19.2 V hammer drill model 315-CS1015*. Not sure if it meets the specs. Will it work?

    1. If the drill manufacturer does not list the items shown as our requirements I would question whether they will meet your needs. See the following which is also shown on our website.

      Cordless Drill Minimum Requirements
      You can use any cordless drill brand you choose, as long as it meets the following minimum requirements:

      Side Stabilizer Arm (for a secure two-handed grip)
      1/2” Drill Chuck
      18 Volt/4 Amp Lithium Ion Battery (or higher)
      Brushless Motor Design
      500-750 RPM with a minimum of
      Minimum 725 in/lbs or 820 UWO of torque

  14. I have a Milwaukee 1/2″ cordless hammer/drill/ driver kit Mfr.# 0726-22 ( 28 volt ) with 28 volt Red Lithium batteries. I’m not sure if it brushless. Will this drill 8″ holes ?
    Thanks Larry

    1. In looking at the specs, it should work, but what is not listed is whether it is brushless or not and though it has a 28 volt battery it does not indicate the amp hours of output. In many cases marginal drills will work if you only drill 2-4 holes and that’s it for an hour or so, but if you want to drill 10-20 holes then move and drill another 10-20 holes you’ll want to make certain you aren’t compromising on a cheap drill that will go up in smoke and you’ll be looking for a new drill before your next trip.

  15. I have seen 3 different torque requirements for the K drill. Your owner’s manual says a minimum of 650in/lb, your product box says a minimum of 700in/lb, and your “drill minimum requirements” on your website says 725in/lb. What is it? I have a Ridgid Genx5 brush-less with a rating of 700in/lb. I would love to buy your product but I cannot afford to also invest in a larger drill. I know you receive endless questions about “will my drill work”, and I am sorry, but with different numbers coming from the manufacturer it is difficult to determine whether mine will work or not.

    1. Our owners manual indicates a minimum of 725 in/lbs of torque and this is still the minimum drill requirement to operate either the 6″ or 8″ K-Drill. Further minimum requirements include Brushless, 4 amp/hour lithium Ion batteries, 500-750 RPM speed range setting, 1/2″ chuck with side stabilizer support arm.

  16. When placing the auger onto the ice, do you recommend placing something in between the drill and the ice? Wondering if slush or any snow on the drill with affect it negatively.

    1. If you are done drilling for a while I’d take off the battery and put it someplace to keep it warm until you’re ready to use again. Using common sense not to lay the drill in the water so it’s not getting the internal components wet is wise. I don’t think throwing it into a snowbank blocking all the drill body venting would be good, but simply laying it on top of the ice would be acceptable.

  17. Can you tell me if the K-drill will fit within the Kolpin Rhino Grip Pro brackets? I am curious because of the larger shaft diameter and the double flighting. Thanks.

    1. I have not personally mounted a K-Drill in these upright brackets. I know it would work to fit around the drive shaft on the top end of the drill, but due to the flighting it may only rest in the brackets on the bottom end, so an additional bungey cord may be necessary to hold the bottom of the K-Drill in position during transit.

  18. How does the Milwaukee 2810 compare to the 2703 in terms of holes drilled per same battery ?

    1. Number of holes from comparable battery is close to identical. Very dependent upon 2810 speed setting.

  19. Your list of drills does not include the newer Milwaukee drills, like the 2705-20 and 2706-20. Has either drill been tested with the Kdrill ? Does the One-Key app on these models help by setting the max RPM, torque, or other settings within the app ?


    1. At this time we have not tested the latest Milwaukee drills with these features.

  20. Do have any plans to make a carry case to fit auger and drill to strap on your back to keep your hands free. Any thoughts on this?

    1. No plans for a backpacking model for this year.

  21. I think a great accessory for this product would be some kind of carrying bag that you could put on your back to carry. Any thoughts on this?

    1. Presently not in plans for this seasons’ production.

  22. Hi, can I purchase new blades from my local dealer or do I have to order them online?

    1. If your local dealer is carrying replacement blades, you can purchase through them. If they don’t have what you’re looking for you may order online at or call direct 952/224-3649.

  23. If not is there a Makita that fits the bill and the 3 amp battery will it work I gust have lots of them?

    1. You may use any drill you wish as long as it meets the requirements shown on our website.

  24. Do you have any info on how many holes can be drilled with the 6” vs the 8” on a charge taking into account the same depth of ice, same battery and drill?
    (Milwaukee M18 model 2703-20 with 9 amp hr battery)

    1. Our tests indicate with all factors being equal the 8″ K-drill completes 12-15% less holes than the 6″ K-drill on a fully charged battery. Of course the 8″ K-Drill is removing 36% more material than the 6″.

  25. I had received a drill set combo for my birthday and i dont know anything about it but im wondering if this would for for a k drill thank you for your time

    1. Major Things to remember
      1) Be certain the drill settings are correct before connecting to the K-Drill – do not Dry-fire (running the auger without a load on the drill)
      2) Keep blades covered until ready to drill ice – Blades are very sharp!!
      3) Read the manual and watch the U-Tube videos before going out on the ice.

  26. Haven’t tried my K drill paired with the Milwaukee fuel drill on the ice yet but it seems to make a clunky noise when I let go of the trigger and the drill stops. Is this normal?

    1. The Milwaukee drill has dynamic braking as a safety feature which stops the rotation of the drill immediately upon release of the trigger. When coupled with an auger of 6″ or 8″ in diameter this momentum to stop is very hard on the drill. It should only be run when there is a load on the drill. Sometimes you may want to support the drill with your gloved hand, in the smooth shaft area (below the float) just to spin off the water and ice. This load is enough to smooth out the stop of the drill.

  27. In a fish house with 110 is a corded drill alright to use? I have a dewalt and it has plenty of torque. It’s variable speed.

    1. I’ve been told by Dewalt that the 110 volt drill should adequately carry the load. They just have concerns of extension cords and water and issues of dealing with high voltage while possibly standing in water. Always better having a drill with a restricted/limited speed in order to maintain control while drilling.

  28. Do you have a drive adapter that fits the Ion auger system? We were fishing a tournament and had to purchase a new auger bit so I bought the K-drill and was going to mount on my Ion auger so I did not have to purchase a drill too at this time but this did not work. The shaft on the Ion is smaller diameter than the drive adapter on the K-Drill and thus it is not stable.

    1. Our adapter for the Clam Plate IDRLADPC also fits the Ion power head. This adapter retails for $14.95. You will notice that the K-Drill will cut with this power head, but because it is turning much slower than you would experience with a standard hand drill, it will not move the chips out of the hole as well so will not be as efficient.

  29. I have the Dewalt drill #DCD996B I don’t see this one listed on the list of products that will work but it seems to meet all the requirements just wondering if this drill will work as well as the other ones?

    1. The Dewalt DCD996 and DCD991 both have the same work output. The only difference is that the DCD991 is a Drill/Driver and the DCD996 is a hammerdrill. Both will work for the K-Drill application as long as the drive selection is in the ‘DRILL’ mode.

  30. On your site I do not see where I can order an adapter (IDRLADPC) for my Clam drill plate? I also want to order the 12″ extension. Any help direction would be appreciated.
    Thank you

    1. If you look under the ‘Shop’ section at the header you’ll find it and be able to place the order.

  31. It is my understanding that you have increased the diameter of the float on the kdrill. If so, is there concern that the drill could come off and disappear down the hole? I brought this question up at the St Paul Ice Show and the guy there suggested I just contact you to see about get the larger size replacement. Would there be a charge? If so, how much.


    1. The float material is 3.13 and has been the same for the past several years.

  32. How about the m18 2603-20? Will this meet the requirements for the k drill.

    1. The Milwaukee 2603-20 was the first of approved Milwaukee drills and has been replaced by Milwaukee with the 2703-20. The new Milwaukee delivers nearly double the torque of the old 2603-20 and doesn’t weigh any more.

  33. just bought one and haven’t tried it on ice yet….. just playing with it but It seems to stop vary abruptly …thinking this will kill the drill???

    1. The Milwaukee drills have a dynamic braking system that does stop the drill abruptly. Not noticeable on small diameter bits, but very evident with larger mass of the K-Drill. Strongly recommend not “Dry Firing” the drill with the K-Drill attached. It needs to have a load on the drill to cushion the stopping forces.

  34. Is there a difference between Dewalt DCD996 and DCD996P2 that keeps it from working with Kdrill 8 inch model?

    1. DCD996 or DCD996b is the bare drill itself and the DCD996P2 is the package deal with 2 batteries, charger, side arm and carrying case. Same drill (hammerdrill) just packaged with more goodies.

  35. Hi, I purchased a K Drill from Cabela’s. Was it supposed to come with the Drive Adapter because there was not one in the box???

    1. Sarah,
      It comes with a drive adapter to attach to an electric drill chuck, but to attach to a Clam Plate, you must purchase the Clam Adapter IDRLADPC.

  36. Couple things, since theres no registration are you going to stand behind your product when the receipt fades away in a year & did you change the flighting as this auger does not match the picture in the owners manual & if so why & what do the changes do to the performance? Is the new spacing not alowing all the shavings to come all the way up, hence the binding?

    1. Your only means of assured warranty at this time is hanging on to your receipt for that first year.

  37. Do you sell M18 drills with just one battery and a case?
    I don’t need another charger and already have one good battery; just need the drill and a single battery.

    1. We only offer the complete drill kit with 2 batteries, charger, drill, side arm and carrying case. It is possible to purchase the drill 2703-20 and battery 48-11-1850 separately from online or contractor outlet stores.

  38. I recently purchased the Milwaukee drill Model #2703-22. I’m clear that the drill needs to be set on the DRILL mode and on the Level 1 RPM setting, but what should the Clutch dial be set to? It has settings from 2-24. I noticed this question was asked earlier but your answer to did not address the clutch setting. Thanks.


    1. Drill needs to be set on ‘1’ for the low speed-high torque setting. Collar to be set in ‘drill’ mode rather than ‘screw’ mode. When in the drill mode the collar setting for the torque does not come into play in the operation of the drill

  39. Hello,

    Is the K-Drill shank a 7/16″ hex flat style?

    Wondering if it’s compatible with Milwaukee’s QUIK-LOK™ Chuck: For keyless, one-handed bit changes. Accepts most 7/16″ hex flat or groove shank bits

    1. No it is not compatible.

  40. How strong is the auger when clearing out pre drilled holes that are starting to freeze up? I.e. Reusing the holes in my shack…

    1. The K-Drill works marvelously for re-drilling old holes. Wherever you set the tip is where it drills. No binding.

    2. The K-drill shank is 1/2″ so you must have a drill that can open up enough to accept a 1/2″ drill.

    3. By going online for your preferential drill manufacturer they will categorize their drills by their chuck size or power. 1/2″ drills are very common, just get one with the correct specs. See our requirements.

  41. Do you have an adapter for an sds drill?

    1. Sorry, there is no adapter for Slotted Drive System drills at this time.

  42. I just purchased your K-Drill with the Milwaukee M18 Fuel Model #2703-22. What torque setting number on the drill should I use for best ice drilling?

    1. Use the normal Drill mode, not the driver mode. Even at the max setting, the auger will stall.

  43. will a Milwaukee model 2701-21p drill work on the k drill?

    1. Sorry John. That model does not meet the requirements.

  44. Just saw your video and at the end it said you could put the KDrill on a strikemaster powerhead. I have the 8 inch KDrill and love it. Will it fit the Honda lite powered head? I have a 10 inch bit and a lot falls though a 10 inch hole would love to put the KDrill 8 inch on. Thank you and have a great day.

    1. If your Honda uses a 7/8″ shaft, it may work. Some modification to the K-Drill shaft may be required in order to allow for the connecting bolt.

  45. Do you have any Canadian dealers

    1. Yes, we have multiple outlets for the K-Drill, please lookup dealers in our K-Drill website by noting your zip code.

  46. Do you have any reconditioned 8″ units in stock

    1. Not at this time, but be sure to check the Shop page occasionally. We’ll list them here when available…

  47. Will my Dewalt dc777 20v brushless work, I asked at Runnings and no one could answer?

    1. No it won’t. This drill lacks the required torque.

  48. Is there an adapter to fit the k drill to the ion power head?

    1. Not at this time.

  49. Can you use a Milwaukee m18 fuel hammer drill?

    1. Only if it meets the minimum specs and has a normal “Drill” mode…

  50. Does this work with a Rigid Gen 5X brushless 18V drill? It has a 2 amp hour (high capacity) battery.

    1. Sorry, it will not.

    2. will a ridgid 5x brushless hammer drill work with the 4 amp battery it seems to meet the requirements if not why so?

    3. This drill has slightly less torque than required. It may work with the 6″ K-Drill, but is not officially approved. Without ample torque, the auger may stall frequently.

  51. Is there a way of extending about 6″ – 8″? I am tall with a bad back. Without an extender, the drill is a little short for me and the 12″ extender is too long.

    1. Sorry, we only offer the 12″ extensions.

  52. Will the Milwaukee 2607-20 work with the 8″ auger?

    1. No, it will not.

  53. Will the Milwaukee 2755-20 work with the k drill?

    1. Afraid not.

  54. How thick of ice can I cut without the extension. Thanks!

    1. 36″

  55. Any plans on a 10ln. bit? That would be great love my 8in.

    1. Sorry, no plans for a larger auger size.

  56. I am up in Canada and it is not uncommon for the ice to be 4’ thick. Can this drill be used at that depth? I can’t see if you sell an extension .

    1. Yes, 12″ extensions are available. They can be stacked, so there really is no limit to how thick the ice can be…

  57. will a kdrill work properly paired with the new strikemaster lithium or will there not be enough rpms

    1. Unknown. It has not been tested as of yet.

  58. Hello, just bought a 8″ k- drill. Love how it works on a milw. Fuel m18. Wondering if it’s been tested on any power heads? And witch one would you recommend? And what a guy needs to make it work. Please and thank you!

    1. Via the engineering department: “The K-Drill is compatible with power heads having a 7/8” output shaft and that turn clockwise when viewing from the top. Strikemaster will use the same 5/16” bolt going through the shaft and Eskimo uses a 3/8” bolt, which means it may be necessary to either add a hole, at 90 degrees to existing hole in the K-Drill shaft, or drill out the existing hole in the K-Drill shaft and secure with a through bolt.”

  59. Yes, this drill meets the requirements.

  60. A drill that is not brushless will still work, but may not survive long because of the load put on the drill.

  61. I have a Milwuakee Fuel 18 brushless drill with two batteries, what is the best settings for drilling holes with kdrill? brand new, just got for this winter! Thanks

    1. Always use the low-gear setting in normal “drill” mode.

  62. If I order the kdrill with the Milwaukee drill, what size are the batteries and how many does it come with? not seeing any of that info on the site. Thank you for the help!

    1. Comes with two 5 Amp Red Lithium batteries, and the charger.

  63. I’m curious if something is maybe out of spec with my auger. I was under the understanding that the k drill would fit on strikemaster powerheads so I tried it on my strikemaster Honda lite this evening and was unable to get the holes to line up. It was close but not close enough to get threaded. Let me know if this should be able to work on my powerhead. I have a drill too but was hoping to use the powerhead late season.

    1. This setup should work. Please contact our support department and attach a photo if you can…

  64. My wife bought me the Milwaukee m18 set with redlithium battery packs. Will this work for a kdrill unit?

    1. Yes, this is our top recommended drill.

  65. Is there a safety option to keep the auger from going to the bottom of the lake, when as you already know ALL, I repeat ALL battery operated drills the chuck never stays tight and do come loose repeatedly, I own Dewalt 20V set, Craftsman 19.2V, and a Milwaukee 18V set as I work on houses for a living All were bought in hopes the chuck coming loose would stop, Never has, so your answer to the bottom of the lake??????????????

    1. Yes, that is the purpose of the foam float attached to the upper part of the auger’s shaft.

  66. I have an 8″ Kdrill 3 or 4 seasons old. The new blades I purchased at the sporting goods retailer are not the same size as my original blades. Has there been changes to the design? What should I do?

    1. The older K-Drills had a slightly different design. You can still get those blades, but you’ll need to order direct. Please call the office at 952-224-3649.

  67. Yes, that drill should work well for both.

  68. Just curious if the reconditioned units come with all the benefits:
    Sharpened blades for life
    1 year warranty

    1. Yes, same warranty and benefits as a new one.

  69. I bought my Kdrill four or five years ago and love it. I have scene moves to Idaho and am now dealing with more slush pockets and now the head keeps freezing up on me. Have you addressed this issue and if so how can I get the head replaced. Thank you!

    1. Yes, we have fixed that problem. The original design of the cutting head from the first K-Drills had a step below the center tip that prevented a smooth flow of chips off the center tip. Once the center tip and surrounding surface packed with ice shavings it stopped the entire drill from moving through the ice. The latest design has a smoother transition that allows the chips and shavings from the center tip to slide onto the area of the cutting blades and be carried out with the chips from the main chipper blades, hence making the K-Drill work through a wider range of drilling conditions. We can upgrade older K-Drills to the new design if you send it in. There is no cost beyond the in-bound shipping.

      K-Drill Systems
      6667 West Old Shakopee Road
      Suite 102
      Bloomington, MN 55438

  70. I have a cordless 1/2″ Milwaukee 18v lithium driver/drill. Category 2601-20, will this work with the 8″ K Drill?

    1. Afraid not Dan. This drill is not brushless (meaning overheating the motor will be a problem) and does not have the torque required.

  71. I have a 20v dewalt and use the clam plate, will the Kdrill fit that or would I need an adapter?

  72. Do you guys offer a veteran discount?

    1. Yes, please contact Corey at the office: 952-224-3649 He’ll take care of you.

  73. Which of the DeWalt drills do you recommend for optimal use of the Kdrill?

    1. The DCD991P2 is a great choice.

  74. What model number Milwaukee drill do you guys send with your drill/ auger combo? Thanks

    1. As of this date, it’s #2703-22

  75. Hammer drills, in hammer mode, should not be used with the K-Drill. Normal drill mode is what you always want. Your drill should be more than adequate.

  76. What constitutes a reconditioned k-drill.

    1. Generally, reconditioned product has been used by our staff, writers, pros and other VIP types. Each drill is thoroughly checked, worn parts are replaced, and it’s fitted with newly sharpened blades.

  77. Looks like their drill is a little light on the torque at 650…

    However, 650 should be adequate for the 6″ K-Drill.

  78. Yes, that should work well. Be sure to use the normal “Drill” mode in the low-gear setting.

  79. Dewalt no longer uses max torque in the specs for their drills. They now uses AWO and MWO to determine the “power” of the drill. Since your website says the minimum requirement to use the K Drill is 750in/lbs, how can I tell if a certain Dewalt drill has enough torque?

    1. Here’s a good article that explains the conversions…

      If the drill is of true professional quality, rather than the DIY types, and meets the 18 volt, half-inch, brushless requirements, it should be more than adequate.

  80. i was lucky enough to be a test participant of the 8 inch auger which i mated to a 60v dewalt – absolutely perfect. Love it!

    Can you resharpen the blades for me? Can i buy additional blades?

    1. Thanks Tom! The 8″ model is our most popular.

      You can buy new blades here…

      and, Yes, we will re-sharpen your old K-Drill blades too. More info here:

  81. So I have a Milwaukee M18 1/2” high toque impact wrench, do you make an adaptor for that?

    1. Sorry, the impact wrench will not work. You’ll need something with a standard drill function.

  82. I have a 50 volt Strikemaster drill that I would like to put the k-drill on. The shaft of the Strikemaster is 7/8″ Do you have an adapter that will fit this shaft?

    1. No need. The K-Drill will fit directly.

  83. Hi,
    I am local. Can I personally pick up the drill at your location?



    1. Yes. We are open M – F 8am to 4:30pm

  84. Do I need to register the Kdrill I bought at the Vexlar store in Bloomington on 9/14/2017?

    I’m not seeing anything in the website to register so I just assume I hold on to the receipt?

    Keith Ricke

    1. Correct. No need to register. Just hang on to your receipt.

Leave a Reply to Michael Cancel reply

Your email address will not be published.